Difference between revisions of "Electrical-Mechanical Equipment"

From energypedia
***** (***** | *****)
m
***** (***** | *****)
m
 
(37 intermediate revisions by 6 users not shown)
Line 1: Line 1:
== [[Category:Hydro]]Introduction  ==
 
  
<u>disambiguation</u>:<br>
+
[[Portal:Hydro|► Back to Hydro Portal]]
  
grid connection<br>
+
= Overview =
  
island / isolated grids<br>
+
-> See article [[Micro Hydro Power (MHP) Plants|Micro Hydro Power (MHP) Plants]]
  
battery storage / charging stations
+
<br/>
  
== '''Off-Grid Battery-Based Microhydro-Electric Systems'''  ==
+
= Turbine Types<br/> =
  
<span>Most small off-grid hydro systems are battery-based. Battery systems have great flexibility and can be combined with other energy sources, such as wind generators and solar-electric arrays, if the stream is seasonal. Because stream flow is usually consistent, battery charging is as well, and it´s often possible to use a relatively </span>
+
A [[Steffturbine - Hydropower Turbine|turbine]] converts the energy in falling water into shaft power. There are various types of turbine which can be categorized in one of several ways. The choice of turbine will depend mainly on the pressure head available and the design flow for the proposed hydropower installation. As shown in table 2 below, turbines are broadly divided into three groups; high, medium and low head, and into two categories: impulse and reaction.<br/>
  
small
+
The difference between impulse and reaction can be explained simply by stating that the impulse turbines convert the kinetic energy of a jet of water in air into movement by striking turbine buckets or blades - there is no pressure reduction as the water pressure is atmospheric on both sides of the impeller. The blades of a reaction turbine, on the other hand, are totally immersed in the flow of water, and the angular as well as linear momentum of the water is converted into shaft power - the pressure of water leaving the runner is reduced to atmospheric or lower.
  
battery bank. Instantaneous demand (watts) will be limited not by the water potential or turbine, but by the size of the inverter.
+
{| align="right" cellpadding="0" border="1" style="width: 100%"
 +
|-
 +
| style="vertical-align: top" rowspan="2" |
 +
'''<span>Turbine</span>'''<br/>
  
<span>The following illustration includes the primary components of any off-grid battery-based microhydro-electric system..</span>
+
'''Runner'''
  
picture... <br>&nbsp;
+
| style="text-align: center;  vertical-align: top" colspan="3" |
 +
'''<span>Head</span>'''
  
== '''Off-Grid Batteryless Microhydro-Electric Systems''' ==
+
'''pressure'''
  
<span>If the stream has enough potential, one may decide to go with an AC-direct system. This consists of a turbine generator that produces AC output at 120 or 240 volts, which can be sent directly to standard household loads. The system is controlled by diverting energy in excess of load requirements to dump loads, such as water- or air-heating elements. This technique keeps the total load on the generator constant. A limitation of these systems is that the peak or surge loads cannot exceed the output of the generator, which is determined by the stream´s available head and flow. This type of system needs to be large to meet peak electrical loads, so it can often generate enough energy for all household needs, including water and space heating.</span>
+
|-
 +
| style="text-align: center;  vertical-align: top" |
 +
'''High'''
  
<span>The following illustration includes the primary components of any off-grid batteryless microhydro-electric system. </span>
+
| style="text-align: center;  vertical-align: top" |
 +
'''Medium'''
  
<!--{12766841534923}-->picture ....
+
| style="text-align: center;  vertical-align: top" |
 +
'''Low'''<br/>
  
<br>
+
|-
 +
| style="vertical-align: top" |
 +
Impulse
  
&nbsp;
+
| style="vertical-align: top" |
 +
*<span>Pelton</span><br/>
 +
*Turgo
 +
*Multi-jet Pelton<br/>
  
== '''Grid-Tied Batteryless Microhydro-Electric Systems'''  ==
+
| style="vertical-align: top" |
 +
*<span>Crossflow</span><br/>
 +
*Turgo
 +
*Multi-jet Pelton<br/>
  
<span>Systems of this type use a turbine and controls to produce electricity that can be fed directly into utility lines. These can use either AC or DC generators. AC systems will use AC generators to sync directly with the grid. An approved interface device is needed to prevent the system from energizing the grid when the grid is out of action and under repair. DC systems will use a specific inverter to convert the output of a DC hydro turbine to grid-synchronous AC. The biggest drawback of batteryless systems is that when the utility is down, your electricity will be out too. When the grid fails, these systems are designed to automatically shut down.</span>  
+
| style="vertical-align: top" |
 +
*Crossflow<br/>
  
<span>The following illustration includes the primary components of any grid-tied batteryless microhydro-electric system. </span>
+
|-
 +
| style="vertical-align: top" |
 +
Reaction
  
<!--{12766841534924}-->&nbsp;
+
| style="vertical-align: top" |
 +
*<span>Francis</span><br/>
 +
*Pump-as-turbine (PAT)<br/>
  
[[|]]'''<span>Microhydro-Electric</span>''' System Components
+
| style="vertical-align: top" |
 +
*<span>Propeller</span><br/>
 +
*Kaplan<br/>
  
'''Controls'''<span> </span>
+
| style="vertical-align: top" |
 +
<br/>
  
AKA: Charge controller, controller, regulator
+
|}
 
 
<!--{12766841534925}-->[[Image:|Controller]]
 
 
 
&nbsp;
 
 
 
<span>The function of a charge controller in a hydro system is equivalent to turning on a load to absorb excess energy. Battery-based microhydro systems require charge controllers to prevent overcharging the batteries. Controllers generally </span>
 
 
 
send
 
 
 
excess energy to a secondary (dump) load, such as an air or water heater. Unlike a solar-electric controller, a microhydro system controller does not disconnect the turbine from the batteries. This could create voltages that are higher than some components can withstand, or cause the turbine to&nbsp;overspeed, which could result in dangerous and damaging overvoltages.
 
 
 
<span>Off-grid, batteryless AC-direct microhydro systems need controls too. A load-control governor monitors the voltage or frequency of the system, and keeps the generator correctly loaded, turning dump-load capacity on and off as the load pattern changes, or mechanically deflects water away from the runner. Grid-tied batteryless AC and DC systems also need controls to protect the system if the utility grid fails.</span>
 
 
 
== '''Dump Load'''  ==
 
 
 
AKA: diversion load, shunt load
 
 
 
<!--{12766841534926}-->[[Image:|Dump Load 1]]<!--{12766841534927}-->[[Image:|Dump Load 2]]
 
 
 
<span>A dump load is an electrical resistance heater that must be sized to handle the </span>
 
 
 
full
 
 
 
generating capacity of the microhydro turbine. Dump loads can be air or water heaters, and are activated by the charge controller whenever the batteries or the grid cannot accept the energy being produced, to prevent damage to the system. Excess energy is "shunted" to the dump load when necessary.
 
 
 
&nbsp;
 
 
 
&nbsp;
 
 
 
== '''<span>Battery</span> Bank'''  ==
 
 
 
AKA: storage battery
 
 
 
<!--{12766841534928}-->[[Image:|Battery Bank]]
 
 
 
<span>By using reversible chemical reactions, a battery bank provides a way to store surplus energy when more is being produced than consumed. When demand increases beyond what is generated, the batteries can be called on to release energy to keep your household loads operating.</span>
 
 
 
<span>A microhydro system is typically the most gentle of the RE systems on the batteries, since they do not often remain in a discharged state. The bank can also be smaller than for a wind or PV system. One or two days of storage </span>
 
 
 
is
 
 
 
usually sufficient. Deep-cycle lead-acid batteries are typically used in
 
 
 
these
 
 
 
systems. They are cost effective and do not usually account for a large percentage of the system cost.
 
 
 
&nbsp;
 
 
 
== '''Metering'''  ==
 
 
 
<span>AKA: battery monitor, amp-hour meter, watt-hour meter</span>
 
 
 
<!--{12766841534929}-->[[Image:|Metering]]
 
 
 
<span>System meters measure and display several different aspects of your microhydro-electric system´s performance and status—tracking how full your battery bank is, how much electricity your turbine is producing or has produced, and how much electricity is being used. Operating your system without metering is like running your car without any gauges—although possible to do, it´s always better to know how well the car is operating and how much fuel is in the tank.</span>
 
 
 
&nbsp;
 
 
 
[[|]]'''<span>Main DC</span>''' Disconnect
 
 
 
== '''AKA: Battery/Inverter disconnect'''  ==
 
 
 
<!--{127668415349210}-->[[Image:|Main DC Disconnect]]
 
 
 
<span>In battery-based systems, a disconnect between the batteries and inverter is required. This disconnect is typically a large, DC-rated breaker mounted </span>
 
 
 
in a
 
 
 
sheet-metal enclosure. It allows the inverter to be disconnected from the batteries for service, and protects the inverter-to-battery wiring against electrical faults.
 
 
 
&nbsp;
 
 
 
&nbsp;
 
 
 
== '''Inverter'''  ==
 
 
 
<span>AKA: DC-to-AC converter </span>
 
 
 
<!--{127668415349211}-->[[Image:|Battery-Based Inverter]]<span>Inverters transform </span>
 
 
 
the DC electricity stored in your battery bank into AC electricity
 
 
 
for powering household appliances. Grid-tied inverters synchronize the system´s output with the utility´s AC electricity, allowing the system to feed hydro-electricity to the utility grid. Battery-based inverters for off-grid or grid-tied systems often include a battery charger, which is capable of charging a battery bank from either the grid or a backup generator if your creek isn´t flowing or your system is down for maintenance.
 
 
 
<span>In rare cases, an inverter and battery bank are used with larger, off-grid AC-direct systems to increase power availability. The inverter uses the AC to charge the batteries, and synchronizes with the hydro-electric AC supply to supplement it when demand is greater than the output of the hydro generator.</span>
 
 
 
[[|]]'''<span>AC</span>''' Breaker Panel
 
 
 
AKA: mains panel, breaker box, service entrance
 
 
 
<!--{127668415349212}-->[[Image:|AC Breaker Panel]]
 
 
 
<span>The AC breaker panel, or mains panel, is the point at which all of a home´s electrical wiring meets with the provider of the electricity, whether that´s the grid or a microhydro-electric system. This wall-mounted panel or box is usually installed in a utility room, basement, garage, or on the exterior of a building. It contains a number of labeled circuit breakers that route electricity to the various rooms throughout a house. These breakers allow electricity to be disconnected for servicing, and also protect the building´s wiring against electrical </span>
 
 
 
fires.
 
 
 
<span>Just like the electrical circuits in your home or office, a grid-tied inverter´s electrical output needs to be routed through an AC circuit breaker. This breaker is usually mounted inside the building´s mains panel. It enables </span>
 
 
 
the
 
 
 
inverter to be disconnected from either the grid or from electrical loads if servicing is necessary. The breaker also safeguards the circuit´s electrical wiring.
 
 
 
'''&nbsp;'''
 
 
 
[[|]]'''Kilowatt-Hour Meter'''
 
 
 
<span>AKA: KWH meter, utility meter</span>
 
 
 
<!--{127668415349213}-->[[Image:|Kilowatt-Hour Meter]]
 
 
 
<span>Most homes with grid-tied microhydro-electric systems will have AC electricity both coming from and going to the utility grid. A multichannel KWH meter keeps track of how much grid electricity you´re using and how much your RE system is producing. The utility company often provides intertie-capable meters at </span>
 
 
 
no
 
 
 
cost.
 
 
 
'''&nbsp;'''
 
 
 
'''&nbsp;'''
 
 
 
'''&nbsp;'''
 
 
 
'''&nbsp;'''
 
 
 
'''&nbsp;'''
 
 
 
'''&nbsp;'''
 
 
 
== ''''Turbines'types'''  ==
 
 
 
<span><!--{127668415349214}-->[[Image:]]</span>
 
 
 
<span>A turbine converts the energy in falling water into shaft power. There are various types of turbine which </span>
 
 
 
can be
 
 
 
categorised in one of several ways. The choice of turbine will depend mainly on the pressure head available and the design flow for the proposed hydropower installation. As shown in table 2 below, turbines are broadly divided into three groups; high, medium and low head, and into two categories: impulse and reaction.
 
 
 
{| cellpadding="0" border="1"
 
|-
 
| valign="top" rowspan="2" | <br>
 
'''<span>Turbine</span>'''
 
 
 
'''Runner'''
 
 
 
| valign="top" align="center" colspan="3" |
 
'''<span>Head</span>'''
 
  
'''pressure'''
+
<br/>
  
|-
+
<br/>
| valign="top" align="center" |
 
'''High'''
 
  
| valign="top" align="center" |
+
<br/>
'''Medium'''
 
  
| valign="top" align="center" |
+
<br/>
'''Low'''<br>
+
*For further information, click [[Steffturbine - Hydropower Turbine|here]].<br/>
 +
*For information on Pump-as-Turbine, click [[:File:Pump as Turbine (PaT) Manual.doc|here]].
  
|-
+
<br/>
| valign="top" |
 
Impulse
 
  
| valign="top" |
+
[[Electrical-Mechanical Equipment#toc|►Go to Top]]
<span>Pelton </span>
 
  
Turgo
+
= Generators =
  
Multi-jet Pelton <br>
+
*[[Thermo Electric Generators|Thermo Electric Generators]]<br/>
  
| valign="top" |
+
<br/>
<span>Crossflow </span>
 
  
Turgo
+
== Established Producers of Hydro Generators ==
  
Multi-jet Pelton <br>
+
Marelli
  
| valign="top" |
+
== Induction Motor as Generator ==
Crossflow
 
  
|-
+
= Controller - Function Principles<br/> =
| valign="top" |
 
Reaction
 
  
| valign="top" |
+
[[File:Mhp-scheme.jpg|thumb|center|605px|Elements of a Micro Hydro Power Scheme|alt=Elements of a Micro Hydro  Power Scheme]]<br/>
<span>Francis </span>
 
  
Pump-as-turbine (PAT) <br>
+
A Load- or Flow- controller ensures that the '''power output does not exceed the power demand''' and power output is stable (e.g. 230V, 50 Hz).
  
| valign="top" |
+
Water turbines, like petrol or diesel engines, will '''vary in speed as load is applied''' or relieved. Although not such a great problem with machinery which uses direct shaft power, this speed variation will seriously '''affect frequency and voltage''' output from a generator.
<span>Propeller </span>
 
  
Kaplan <br>
+
Traditionally, hydraulic or mechanical speed governors altered flow as the load varied. Nowadays usually electronic load controller (ELC) are used. These prevent speed variations by continuously adding or subtracting an artificial load ('''load controller'''). In that in effect, the turbine is working permanently under full load and the ELC diverts excess energy into a dump load, mostly a heater.&lt;/span&gt; The traditional kind of equalizing power in and output by controlling the flow is usually also automatised ('''flow control'''). Thereby the ELC steers a valve which regulates the amount of water inflowing.
  
| valign="top" |
+
In case of more power demand than supply the controller cuts off single users (clusters) in order to keep voltage and frequency constant for the others (first and second class connections). Load or flow controller are placed between generator output and the consumer line.<br/>
&nbsp;
 
  
|}
+
[[Electrical-Mechanical Equipment#toc|►Go to Top]]<br/>
  
'''&nbsp;'''
+
== Controller Types ==
  
<span>The difference between impulse and reaction can be explained simply by stating that the ''impulse'' turbines convert the kinetic energy of a jet of water in air into movement by striking turbine buckets or blades - there is no pressure reduction as the water pressure is atmospheric on both sides of the impeller. The blades of a ''reaction'' turbine, on the other hand, are totally immersed in the flow of water, and the angular as well as linear momentum of the water is converted into shaft power - the pressure of water leaving the runner is reduced to atmospheric or lower. </span>
+
Fluctuating energy demand requires a mechanism which either regulates the water input into the turbine (= flow control) or by diverting excess energy from the consumer connection (= ballast load).
  
== '''Load factor'''  ==
+
For small micro or pico hydropower sites it's sometimes not easy to find the right controller. There is a lower price limit of several 100 USD even for only 1 or 2 kW power. In such cases there may be thought of manual control.
  
<span>The load factor is the amount of power used divided by the amount of power that is available if the turbine were to be used continuously. Unlike technologies relying on costly fuel sources, the 'fuel' for hydropower generation is free and therefore the plant becomes more cost effective if run for a high percentage of the time. If the turbine is only used for domestic lighting in the evenings then the plant factor will be very low. If the turbine provides power for rural industry during the day, meets domestic demand during the evening, and maybe pumps water for irrigation in the evening, then the plant factor will be high. </span>
+
[[Electrical-Mechanical Equipment#toc|►Go to Top]]
  
<span>It is very important to ensure a high plant factor if the scheme is to be cost effective and this should be taken into account during the planning stage. Many schemes use a 'dump' load (in conjunction with an electronic load controller - see below), which is effectively a low priority energy demand that can accept surplus energy when an excess is produced e.g. water heating, storage heaters or storage cookers. </span>
+
=== Load Control ===
  
== '''Load control governors'''  ==
+
The electric load controller (ELC) keeps outgoing Voltage and Frequency stable. Therefore the load on the generator has to be kept stable. The controller adds and subtracts an artificial load (heater) in a way to neutralise the fluctuations on the consumer side.
  
<span>Water turbines, like petrol or diesel engines, will vary in speed as load is applied or relieved. Although not such a great problem with machinery which uses direct shaft power, this speed variation will seriously affect both frequency and voltage output from a generator. Traditionally, complex hydraulic or mechanical speed governors altered flow as the load varied, but more recently an electronic load controller (ELC) has been developed which has increased the simplicity and reliability of modern micro-hydro sets. The ELC prevents speed variations by continuously adding or subtracting an artificial load, so that in effect, the turbine is working permanently under full load. A further benefit is that the ELC has no moving parts, is very reliable and virtually maintenance free. The advent of electronic load control has allowed the introduction of simple </span>
+
[[File:Controler.jpg|thumb|right|734px|Controler|alt=Controler.jpg]]
  
and
+
<br/>
  
efficient, multi-jet turbines, no longer burdened by expensive hydraulic governors.&nbsp;
+
<br/>
  
<br>
+
=== Ballast Load ===
  
== Controller: <br> ==
+
If energy demand is temporarily low the excess energy is dumped. It's converted into heat by some heat elements either in water or air. To increase an mhp's overall efficiency such excess power could be utilised as well. Therefore some storage technology would be required. Battery charging, freezers, water pumping or heat storage may be options.
  
<!--{12766848790530}--><!--{12766848790531}--><!--{12766848790532}-->
+
Regarding intelligent load management: [[:File:Operation and Maintenance of Small Hydro.pdf|Operation and Maintenance of Small Hydro]] by Dr Nigel Smith, Dr Philip Taylor and Tim Matthews
  
<span id="1274973221030S" style="display: none">&nbsp;</span>  
+
<br/>
  
<!--{12766848790533}--><!--{12766848790534}--><!--{12766848790535}--><span lang="DE" style="font-size: 11pt; color: black; font-family: tahoma">Function </span><span lang="DE" style="font-size: 11pt; color: black; font-family: tahoma">[[Image:Mhp-scheme.jpg|right|558x386px|Elements of a Micro Hydro  Power Scheme]]principles</span><br>
+
=== Flow Control ===
  
Load- or Flow- controller ensure that the power output does not exceed the power demand (e.g. 230V, 50 Hz). <br>If flow of water in a MHP-station is constant the energy output of a turbine/generator is constant as well. Power demand is usually fluctuating over the time (e.g. day/night). If supply is higher than demand, excess energy must be diverted, dumped. alternatively the water flow can be reduced which results in less power output. <br>In case of more power demand than supply the controller cuts of the of demand line. <br>Load controller are placed between generator output and the consumer line.<!--{12766848790536}--> <span lang="DE" style="font-size: 11pt; color: black; font-family: tahoma" />
+
regulates the amount of water into the turbine in order to match power output and power demand. Nowadays flow control is done mostly via electronics, which steer a valve
  
<br>
+
[[File:Flow-control.jpg|thumb|center|834px|principle flow control|alt=principle flow control]]
  
<br>
+
<u>Manual Flow Control:</u>
  
<br>
+
In very small schemes often all power for lighting and TV is used constantly. Then energy consumption barely alters or does only at certain times. In such cases it can be even practical to train an operator who open / closes a valve manually to stabilise the Voltage. This allows to disclaim a controller, which saves costs and potentially flaws.
  
<br>
+
<br/>
  
<!--{12766848790537}--><!--{12766848790538}--><!--{12766848790539}-->
+
[[Electrical-Mechanical Equipment#toc|►Go to Top]]
  
=== <span lang="DE" style="font-size: 11pt; color: black; font-family: tahoma">Controller Types</span>  ===
+
= Load Factor =
  
==== Load controller:  ====
+
The load factor is the amount of power used divided by the amount of power that is available if the turbine were to be used continuously. Unlike technologies relying on costly fuel sources, the 'fuel' for hydropower generation is free and therefore the plant becomes more cost effective if run for a high percentage of the time. If the turbine is only used for domestic lighting in the evenings then the plant factor will be very low. If the turbine provides power for rural industry during the day, meets domestic demand during the evening, and maybe pumps water for irrigation in the evening, then the plant factor will be high.
  
[[Image:Controler.jpg|right|349x141px|Controler.jpg]]
+
It is very important to ensure a high plant factor if the scheme is to be cost effective and this should be taken into account during the planning stage. Many schemes use a 'dump' load (in conjunction with an electronic load controller - see below), which is effectively a low priority energy demand that can accept surplus energy when an excess is produced e.g. water heating, storage heaters or storage cookers.
  
Electronic circuit, which keeps output power constant in Frequency- and Voltage- parameters.
+
[[Electrical-Mechanical Equipment#toc|►Go to Top]]
  
Fluctuating energy demand requires a mechanism which either regulates the water input into the turbine (= flow control) or by diverting excess energy from the consumer connection (= ballast load).
+
= Further Information =
  
==== Ballast load  ====
+
*[[Control Equipment - Hydropower|Control Equipment - Hydropower]]<br/>
 +
*[[Hydropower - Equipment|Hydropower - Equipment]]<br/>
 +
*[[Steffturbine - Hydropower Turbine|Steffturbine - Hydropower Turbine]]
  
usually electrical heaters in water or air. If energy demand is temporarily low the excess energy is converted into heat.
+
<br/>
  
==== Flow control  ====
+
[[Electrical-Mechanical Equipment#toc|►Go to Top]]
  
regulates the amount of water into the turbine in order to match power output and power demand.
+
= References =
  
Nowadays flow control is done mostly via electronics (which steer a valve)  
+
*General:[[Micro Hydro Power (MHP) Manuals|Micro hydro Power Manuals]]
 +
*[[:File:Good and bad of mini hydro power vol.1.pdf|Good and Bad of Mini Hydro Power]]
 +
*[[:File:Hydro scout guide ET may10.pdf|Micro Hydro Power Scout Guide]]
 +
*[http://practicalaction.org/micro-hydro-power-2 Micro-Hydro Power: Practical Action]
  
[[Image:Flow-control.jpg|left|650x264px|principle flow control]]
+
<references /><br/>
  
 
[[Category:Hydro]]
 
[[Category:Hydro]]

Latest revision as of 10:45, 9 September 2014

► Back to Hydro Portal

Overview

-> See article Micro Hydro Power (MHP) Plants


Turbine Types

A turbine converts the energy in falling water into shaft power. There are various types of turbine which can be categorized in one of several ways. The choice of turbine will depend mainly on the pressure head available and the design flow for the proposed hydropower installation. As shown in table 2 below, turbines are broadly divided into three groups; high, medium and low head, and into two categories: impulse and reaction.

The difference between impulse and reaction can be explained simply by stating that the impulse turbines convert the kinetic energy of a jet of water in air into movement by striking turbine buckets or blades - there is no pressure reduction as the water pressure is atmospheric on both sides of the impeller. The blades of a reaction turbine, on the other hand, are totally immersed in the flow of water, and the angular as well as linear momentum of the water is converted into shaft power - the pressure of water leaving the runner is reduced to atmospheric or lower.

Turbine

Runner

Head

pressure

High

Medium

Low

Impulse

  • Pelton
  • Turgo
  • Multi-jet Pelton
  • Crossflow
  • Turgo
  • Multi-jet Pelton
  • Crossflow

Reaction

  • Francis
  • Pump-as-turbine (PAT)
  • Propeller
  • Kaplan






  • For further information, click here.
  • For information on Pump-as-Turbine, click here.


►Go to Top

Generators


Established Producers of Hydro Generators

Marelli

Induction Motor as Generator

Controller - Function Principles

Elements of a Micro Hydro Power Scheme
Elements of a Micro Hydro Power Scheme


A Load- or Flow- controller ensures that the power output does not exceed the power demand and power output is stable (e.g. 230V, 50 Hz).

Water turbines, like petrol or diesel engines, will vary in speed as load is applied or relieved. Although not such a great problem with machinery which uses direct shaft power, this speed variation will seriously affect frequency and voltage output from a generator.

Traditionally, hydraulic or mechanical speed governors altered flow as the load varied. Nowadays usually electronic load controller (ELC) are used. These prevent speed variations by continuously adding or subtracting an artificial load (load controller). In that in effect, the turbine is working permanently under full load and the ELC diverts excess energy into a dump load, mostly a heater.</span> The traditional kind of equalizing power in and output by controlling the flow is usually also automatised (flow control). Thereby the ELC steers a valve which regulates the amount of water inflowing.

In case of more power demand than supply the controller cuts off single users (clusters) in order to keep voltage and frequency constant for the others (first and second class connections). Load or flow controller are placed between generator output and the consumer line.

►Go to Top

Controller Types

Fluctuating energy demand requires a mechanism which either regulates the water input into the turbine (= flow control) or by diverting excess energy from the consumer connection (= ballast load).

For small micro or pico hydropower sites it's sometimes not easy to find the right controller. There is a lower price limit of several 100 USD even for only 1 or 2 kW power. In such cases there may be thought of manual control.

►Go to Top

Load Control

The electric load controller (ELC) keeps outgoing Voltage and Frequency stable. Therefore the load on the generator has to be kept stable. The controller adds and subtracts an artificial load (heater) in a way to neutralise the fluctuations on the consumer side.

Controler.jpg
Controler



Ballast Load

If energy demand is temporarily low the excess energy is dumped. It's converted into heat by some heat elements either in water or air. To increase an mhp's overall efficiency such excess power could be utilised as well. Therefore some storage technology would be required. Battery charging, freezers, water pumping or heat storage may be options.

Regarding intelligent load management: Operation and Maintenance of Small Hydro by Dr Nigel Smith, Dr Philip Taylor and Tim Matthews


Flow Control

regulates the amount of water into the turbine in order to match power output and power demand. Nowadays flow control is done mostly via electronics, which steer a valve

principle flow control
principle flow control

Manual Flow Control:

In very small schemes often all power for lighting and TV is used constantly. Then energy consumption barely alters or does only at certain times. In such cases it can be even practical to train an operator who open / closes a valve manually to stabilise the Voltage. This allows to disclaim a controller, which saves costs and potentially flaws.


►Go to Top

Load Factor

The load factor is the amount of power used divided by the amount of power that is available if the turbine were to be used continuously. Unlike technologies relying on costly fuel sources, the 'fuel' for hydropower generation is free and therefore the plant becomes more cost effective if run for a high percentage of the time. If the turbine is only used for domestic lighting in the evenings then the plant factor will be very low. If the turbine provides power for rural industry during the day, meets domestic demand during the evening, and maybe pumps water for irrigation in the evening, then the plant factor will be high.

It is very important to ensure a high plant factor if the scheme is to be cost effective and this should be taken into account during the planning stage. Many schemes use a 'dump' load (in conjunction with an electronic load controller - see below), which is effectively a low priority energy demand that can accept surplus energy when an excess is produced e.g. water heating, storage heaters or storage cookers.

►Go to Top

Further Information


►Go to Top

References