Difference between revisions of "Parts of a Biogas Plant"

From energypedia
***** (***** | *****)
***** (***** | *****)
m
 
(37 intermediate revisions by 3 users not shown)
Line 1: Line 1:
  
The feed material is mixed with water in the [[Parts of a biogas plant#Influent collecting tank|influent collecting tank]] The fermentation slurry flows through the &lt;/span&gt;[[Parts of a biogas plant#Inlet and outlet|inlet]]<span style="line-height: 1.5em; font-size: 0.85em;">into the </span>[[Parts of a biogas plant#Digester|digester]]<span style="line-height: 1.5em; font-size: 0.85em;">. The bacteria from the fermentation slurry are intended to produce biogas in the digester. For this purpose, they need time. Time to multiply and to spread throughout the slurry. The digester must be designed in a way that only fully digested slurry can leave it. The bacteria are distributed in the slurry by </span>[[Parts of a biogas plant#Stirring facilities|stirring]] <span style="line-height: 1.5em; font-size: 0.85em;">(with a stick or stirring facilities). The fully digested slurry leaves the digester through the </span>[[Parts of a biogas plant#Inlet and outlet|outlet]]<span style="line-height: 1.5em; font-size: 0.85em;">into the slurry storage.</span>
+
[[Portal:Biogas|►Back to Biogas Portal]]<br/>
  
The biogas is collected and stored until the time of consumption in the [[Parts of a biogas plant#Gasholders|gasholder]]. The [[Parts of a biogas plant#Gas pipe.2C valves and accessories|gas pipe]] carries the biogas to the place where it is consumed by [[Biogas Appliances|gas appliances]]. Condensation collecting in the gas pipe is removed by a water trap.
+
= Overview =
  
Depending on the available building material and type of plant under construction, different variants of the individual components are possible. The following (optional) components of a biogas plant can also play an important role and are described seperatly: [[Optional Parts of a biogas plant#Heating systems|Heating systems]], [[Optional Parts of a biogas plant#Pumps|pumps]], [[Optional Parts of a biogas plant#Weak ring|weak ring]].
+
The feed material is mixed with water in the influent collecting tank The fermentation slurry flows through the inlet into the digester. The bacteria from the fermentation slurry are intended to produce biogas in the digester. For this purpose, they need time. Time to multiply and to spread throughout the slurry. The digester must be designed in a way that only fully digested slurry can leave it. The bacteria are distributed in the slurry by stirring (with a stick or stirring facilities). The fully digested slurry leaves the digester through the outlet into the slurry storage.The biogas is collected and stored until the time of consumption in the gasholder. The gas pipe carries the biogas to the place where it is consumed by gas appliances. Condensation collecting in the gas pipe is removed by a water trap. Depending on the available building material and type of plant under construction, different variants of the individual components are possible. The following (optional) components of a biogas plant can also play an important role and are described seperatly: Heating systems, pumps, weak ring.<br/>
 
 
<br/>
 
  
 
= Influent Collecting Tank<br/> =
 
= Influent Collecting Tank<br/> =
  
{| cellpadding="10" border="0" align="right" style="width: 220px" class="IMGright"
+
{| cellpadding="10" border="0" align="right" class="IMGright" style="width: 220px"
 
|-
 
|-
 
|  
 
|  
[[File:Bgfixeddomeinst.jpg|220px|RTENOTITLE]]
+
[[File:Bgfixeddomeinst.jpg|thumb|right|200px|Bgfixeddomeinst.jpg]]<br/><br/>
 
 
<small class="IMGLEGEND">'''Installation of a fixed-dome plant in Thailand: The influent collecting tank is in front of the photo, the digester and the outlet are located behind it.'''</small><ref name="Photo: Kossmann (gtz/GATE)">Photo: Kossmann (gtz/GATE)</ref><br/>
 
  
 
|}
 
|}
  
== Size and Homogenization<br/> ==
+
'''<u>Size and Homogenization</u>'''<br/>Fresh substrate is usually gathered in an influent collecting tank prior to being fed into the digester. Depending on the type of system, the tank should hold one to two days' substrate. An influent collecting tank can also be used to homogenize the various substrates and to set up the required consistency, e.g. by adding water to dilute the mixture of vegetable solids (straw, grass, etc.), or by adding more solids in order to increase the bio-mass. The fibrous material is raked off the surface, if necessary, and any stones or sand settling at the bottom are cleaned out after the slurry is admitted to the digester. The desired degree of homogenization and solids content can be achieved with the aid of an agitator, [[Pumps_for_Biogas_Plants|pump]]&nbsp;or chopper. A rock or wooden plug can be used to close off the inlet pipe during the mixing process.<br/>
 
 
Fresh substrate is usually gathered in an influent collecting tank prior to being fed into the digester. Depending on the type of system, the tank should hold one to two days' substrate. An influent collecting tank can also be used to homogenize the various substrates and to set up the required consistency, e.g. by adding water to dilute the mixture of vegetable solids (straw, grass, etc.), or by adding more solids in order to increase the bio-mass. The fibrous material is raked off the surface, if necessary, and any stones or sand settling at the bottom are cleaned out after the slurry is admitted to the digester. The desired degree of homogenization and solids content can be achieved with the aid of an [[Parts of a Biogas Plant#Stirring Facilities|agitator]], [[Optional Parts of a biogas plant#Pumps|pump]] or chopper. A rock or wooden plug can be used to close off the inlet pipe during the mixing process.<br/>
 
 
 
<br/>
 
 
 
== Location ==
 
 
 
A sunny location can help to warm the contents before they are fed into the digester in order to avoid thermal shock due to the cold mixing water. In the case of a biogas plant that is directly connected to the stable, it is advisable to install the mixing pit deep enough to allow installation of a floating gutter leading directly into the pit. Care must also be taken to ensure that the low position of the mixing pit does not result in premature digestion. For reasons of hygiene, toilets should have a direct connection to the inlet pipe.
 
 
 
<br/>
 
 
 
 
 
== Inlet and Outle<span style="font-size: 19px; line-height: 23.799999237060547px;">t</span> ==
 
 
 
The inlet (feed) and outlet (discharge) pipes lead straight into the digester at a steep angle. For liquid substrate, the pipe diameter should be 10-15 cm, while fibrous substrate requires a diameter of 20-30 cm. The inlet and the outlet pipe mostly consist of plastic or concrete.
 
 
 
=== Position<br/> ===
 
 
 
Both the inlet and the outlet pipe must be freely accessible and straight, so that a rod can be pushed through to eliminate obstructions and agitate the digester contents. The pipes should penetrate the digester wall at a point below the lowest slurry level (i.e. not through the gas storage). The points of penetration should be sealed and reinforced with mortar.
 
 
 
The inlet pipe ends higher in the digester than the outlet pipe in order to promote more uniform flow of the substrate. In a [[Types of Biogas Digesters and Plants#Fixed-dome plants|fixed-dome plant]], the inlet pipe defines the bottom line of the gas-holder, acting like a security valve to release over-pressure. In a [[Types of Biogas Digesters and Plants#Floating-drum plants|floating-drum plant]], the end of the outlet pipe determines the digester's (constant) slurry level.
 
  
Inlet and outlet pipe must be placed in connection with brick-laying. It is not advisable to break holes into the spherical shell afterwards, this would weaken the masonry structure.
+
<br/>'''<u>Location</u>'''<br/>
  
<br/>
+
A sunny location can help to warm the contents before they are fed into the digester in order to avoid thermal shock due to the cold mixing water. In the case of a biogas plant that is directly connected to the stable, it is advisable to install the mixing pit deep enough to allow installation of a floating gutter leading directly into the pit. Care must also be taken to ensure that the low position of the mixing pit does not result in premature digestion. For reasons of hygiene, toilets should have a direct connection to the inlet pipe.<br/>
  
<u>Toilet Connection at the Inlet</u><br/>
+
<br/>'''<u>Inlet and Outlet</u>'''<br/>
  
--> [[Connection of a toilet to a biogas digester|Household Toilets can be connected to a Biogas Digester.]]<br/>
+
The inlet (feed) and outlet (discharge) pipes lead straight into the digester at a steep angle. For liquid substrate, the pipe diameter should be 10-15 cm, while fibrous substrate requires a diameter of 20-30 cm. The inlet and the outlet pipe mostly consist of plastic or concrete.<br/>
  
<br/>
+
<br/>'''<u>Position</u>'''<br/>Both the inlet and the outlet pipe must be freely accessible and straight, so that a rod can be pushed through to eliminate obstructions and agitate the digester contents. The pipes should penetrate the digester wall at a point below the lowest slurry level (i.e. not through the gas storage). The points of penetration should be sealed and reinforced with mortar. The inlet pipe ends higher in the digester than the outlet pipe in order to promote more uniform flow of the substrate. In a [[Types_of_Biogas_Digesters_and_Plants#Fixed_Dome_Biogas_Plants|fixed-dome plant]], the inlet pipe defines the bottom line of the gas-holder, acting like a security valve to release over-pressure. In a [[Types_of_Biogas_Digesters_and_Plants#Floating_Drum_Plants|floating-drum plant]], the end of the outlet pipe determines the digester's (constant) slurry level. Inlet and outlet pipe must be placed in connection with brick-laying. It is not advisable to break holes into the spherical shell afterwards, this would weaken the masonry structure.<br/>
  
 +
<br/>'''<u>Toilet Connection at the Inlet</u>'''<br/>► [[Connection_of_a_Toilet_to_a_Biogas_Digester|Household Toilets can be connected to a Biogas Digester.]]<br/>
  
 
= Digester =
 
= Digester =
  
<span style="line-height: 1.5em; font-size: 0.85em;">No matter which design is chosen, the digester (fermentation tank) must meet the following requirements:</span>
+
In general terms, digesters consist of the digestion tank as such, which is thermally insulated, plus a heating system, mixer systems and discharge systems for sediments and the spent substrate.<br/><br/>
*'''Water/gastightness''' - watertightness in order to prevent seepage and the resultant threat to soil and groundwater quality; gastightness in order to ensure proper containment of the entire biogas yield and to prevent air entering into the digester (which could result in the formation of an explosive mixture).
 
*'''Insulation''' - if and to which extent depends on the required process temperature, the local climate and the financial means; heat loss should be minimized if outside temperatures are low, warming up of the digester should be facilitated when outside temperatures are high.
 
*'''Minimum surface area''' - keeps cost of construction to a minimum and reduces heat losses through the vessel walls. A spherical structure has the best ratio of volume and surface area. For practical construction, a hemispherical construction with a conical floor is close to the optimum.
 
*'''Structural stability''' - sufficient to withstand all static and dynamic loads, durable and resistant to corrosion.
 
  
<br/>
+
== Raw Material for Biogas Digesters<br/> ==
  
=== Internal and External Forces<br/> ===
+
►[[Material_for_Biogas_Digesters|Read more here .....]]<br/><br/>
  
Two relevant forces act on the digester. The external active earth pressure causes compressive forces within the masonry. The internal hydrostatic and gas pressures causes tensile stress in the masonry. Thus, the external pressure applied by the surrounding earth must be greater at all points than the internal forces. Round and spherical shapes are able to accept the highest forces and distribute them uniformly. Edges and corners lead to peak tensile stresses which can result in cracking.
+
== Types of Biogas Digesters ==
  
<br/>
+
►[[Types_of_Biogas_Digesters_and_Plants|Read more here .....]]<br/><br/>
  
=== Shapes of Digesters<br/> ===
+
== Types of Gasholders for Biogas Plants ==
  
From the standpoint of fluid dynamics and structural strength, an egg-shaped vessel is about the best possible solution. This type of construction, however, is comparatively expensive, so that its use is usually restricted to large-scale sewage treatment plants. The Chinese [[Types of Biogas Digesters and Plants#Types of fixed-dome plants|fixed-dome]] designs are of similar shape, but less expensive. The hemispherical [[Types of Biogas Digesters and Plants#Types of fixed-dome plants|CAMARTEC design]] is optimized in structural strength, but does not make optimal use of the excavation required.
+
[[Types_of_Gasholders_for_Biogas_Plants|Read more here .....]]<br/><br/>
  
Simplified versions of such digester designs include cylinders with conical covers and bottoms. They are much easier to build and are sometimes available on the market as prefabricated units. Their disadvantage lies in their less favorable surface-volume ratio. The cylinder should have a height equal to its diameter. ''Prone cylinders'' have become quite popular on farms, since they are frequently the more favorable solution for small-scale bio-methanation. ''Cuboid digesters'' are often employed in batch-fed systems used primarily for fermenting solid material, so that fluid dynamics are of little interest.
+
= Gas Pipe, Valves and Accessories<br/> =
  
<br/>
+
== Biogas Piping<br/> ==
  
{| cellpadding="10" border="0" align="right" style="width: 378px" class="IMGright"
+
{| cellpadding="10" border="0" align="right" class="IMGright" style="width: 348px"
 
|-
 
|-
 
|  
 
|  
[[File:Digestneck.jpg|378px|RTENOTITLE]]
+
[[File:Bgstirrer.jpg|thumb|right|248px]]<br/><br/>
 
 
<small class="IMGLEGEND">'''Construction of the digester neck with steel reinforcement'''</small><ref name="Photo: Krämer (TBW)">Photo: Krämer (TBW)</ref><br/>
 
  
 
|}
 
|}
  
=== <br/> ===
+
At least 60% of all non-functional biogas units are attributable to defect gas piping. Utmost care has to be taken, therefore, for proper installation. For the sake of standardization, it is advisable to select a single size for all pipes, valves and accessories. The requirements for [[Piping_Systems_for_Biogas_Plants|biogas piping]], valves and accessories are essentially the same as for other gas installations. However, biogas is 100% saturated with water vapor and contains hydrogen-sulfide. Consequently, no piping, valves or accessories that contain any amounts of ferrous metals may be used for biogas piping, because they would be destroyed by corrosion within a short time. The gas lines may consist of standard galvanized steel pipes. Also suitable (and inexpensive) is plastic tubing made of rigid PVC or rigid PE. Flexible gas pipes laid in the open must be UV-resistant.<br/>
 
 
=== Further Reading<br/> ===
 
 
 
Hohlfeld, J.; Sasse, L. (Deutsche Gesellschaft für Technische Zusammenarbeit): Production and utilization of biogas in rural areas of industrialized and developing countries. TZ-Verlagsgesellschaft mbH, Roßdorf, 1986, 278 S.<br/>
 
  
<br/>
+
<br/>[[Biogas_Gas_Pipe,_Valves_and_Accessories#Gas_Pipe|► Read More here...]]<br/><br/>
  
== Gasholders<br/> ==
+
== Water Traps ==
  
Basically, there are different designs of construction for gasholders used in simple biogas plants
+
[[Biogas_Gas_Pipe,_Valves_and_Accessories#Water_Traps|► Read more here....]]<br/><br/>
  
<br/>
+
== Valves ==
  
=== Floating-drum Gasholders<br/> ===
+
[[Biogas_Gas_Pipe,_Valves_and_Accessories#Valves|► Read more here...]]<br/><br/>
  
Most floating-drum gas-holders are made of 2-4 mm thick sheet steel, with the sides made of thicker material than the top in order to compensate for the higher degree of corrosive attack. Structural stability is provided by L-bar bracing that also serves to break up surface scum when the drum is rotated. A guide frame stabilizes the gas drum and prevents it from tilting and rubbing against the masonry. <u>The two equally suitable and most frequently used types are:</u><br/>
+
== Gas Analysis Equipment ==
*an internal rod & pipe guide with a fixed (concrete-embedded) cross pole (an advantageous configuration in connection with an internal gas outlet);
 
*external guide frame supported on three wooden or steel legs.<br/>
 
  
<br/>
+
[[Biogas_Gas_Pipe,_Valves_and_Accessories#Gas_Analysis_Equipment|►Read more here...]]<br/><br/>
  
For either design, substantial force can be necessary to rotate the drum, especially if it is stuck in a heavy layer of floating scum. Any gas-holder with a volume exceeding 5 m<sup>3</sup> should be equipped with a double guide (internal and external).
+
= Stirring Facilities<br/> =
 
 
All grades of steel normally used for gas-holders are susceptible to moisture-induced rusting both in- and outside. <u>Consequently, a long service life requires proper surface protection, including:</u><br/>
 
*thorough de-rusting and de-soiling
 
*primer coat of minimum 2 layers
 
*2 or 3 cover coats of plastic or bituminous paint.<br/>
 
 
 
<br/>
 
 
 
The cover coats should be reapplied annually. A well-kept metal gas-holder can be expected to last between 3 and 5 years in humid, salty air or 8-12 years in a dry climate.
 
 
 
Materials regarded as suitable alternatives to standard grades of steel are galvanized sheet metal, plastics (glass-fiber reinforced plastic (GRP), plastic sheeting) and ferro-cement with a gas-tight lining. The gas-holders of water-jacket plants have a longer average service life, particularly when a film of used oil is poured on the water seal to provide impregnation.
 
 
 
<br/>
 
 
 
=== Fixed-dome Gasholders<br/> ===
 
 
 
A fixed-dome gas-holder can be either the upper part of a hemispherical digester (CAMARTEC design) or a conical top of a cylindrical digester (e.g. Chinese fixed-dome plant). In a fixed-dome plant the gas collecting in the upper part of the dome displaces a corresponding volume of digested slurry.<br/>
 
 
 
<u>The following aspects must be considered with regard to design and operation:</u><br/>
 
*An overflow into and out of the compensation tank must be provided to avoid over-filling of the plant.
 
*The gas outlet must be located about 10 cm higher than the overflow level to avoid plugging up of the gas pipe.
 
*A gas pressure of 1 m WC or more can develop inside the gas space. Consequently, the plant must be covered sufficiently with soil to provide an adequate counter-pressure.
 
*Special care must be taken to properly close the man hole, which may require to weigh down the lid with 100 kg or more. The safest method is to secure the lid with clamps.<br/>
 
 
 
<br/>
 
 
 
<u>The following structural measures are recommended to avoid cracks in the gas-holder:</u><br/>
 
*The foot of the dome (gas-holder) should be stabilized by letting the foundation slab project out enough to allow for an outer ring of mortar.
 
*A rated break/pivot ring should be provided at a point located between 1/2 and 2/3 of the minimum slurry level. This in order to limit the occurrence or propagation of cracks in the vicinity of the dome foot and to displace forces through its stiffening/articulating effect such that tensile forces are reduced around the gas space. Alternatively, the lowest point of the gas-holder should be reinforced by a steel ring or the whole gas-holder be reinforced with chicken mesh wire.<br/>
 
 
 
<br/>
 
 
 
Normally, masonry, ''mortar and concrete are not gas-tight'', with or without mortar additives. Gas-tightness can only be achieved through good, careful workmanship and special coatings. The main precondition is that masonry and plaster are strong and free of cracks. Cracked and sandy rendering must be removed. In most cases, a plant with cracked masonry must be dismantled, because not even the best seal coating can render cracks permanently gas-tight.
 
 
 
<u>Some tried and proven [[Plasters and coats for digesters and gas-holder|seal coats and plasters]]:</u><br/>
 
*'''multi-layer bitumen''', applied cold (hot application poses the danger of injury by burns and smoke-poisoning; solvents cause dangerous/explosive vapors). Two to four thick coats required;
 
*'''bitumen with aluminum foil''', thin sheets of overlapping aluminum foil applied to the still-sticky bitumen, followed by the next coat of bitumen;
 
*'''plastics''', e.g. epoxy resin or acrylic paint; very good but expensive;
 
*'''paraffin''', diluted with 2-5% kerosene, heated up to 100°C and applied to the preheated masonry, thus providing an effective (deep) seal. Use kerosene/gas torch to heat masonry.
 
*multi-layer '''cement plaster '''with water-proof elements
 
 
 
In any case, a pressure test must be carried out before the plant is put in service.
 
 
 
<br/>
 
 
 
=== Plastic Gasholders<br/> ===
 
 
 
Gas-holders made of plastic sheeting serve as integrated gas-holders, as separate balloon/bag-type gas-holders and as integrated gas-transport/storage elements. For plastic (sheet) gas-holders, the structural details are of less immediate interest than the question of which materials can be used.<br/>
 
 
 
<br/>
 
 
 
=== Separate Gasholders<br/> ===
 
 
 
<u>Differentiation is made between:</u><br/>
 
*low-pressure, wet and dry gas-holders (10-50 mbar). Basically, these gas-holders are identical to integrated and/or plastic (sheet) gas-holders. Separate gas-holders cost more and are only worthwhile in case of substantial distances (at least 50-100 m) or to allow repair of a leaky fixed-dome plant. This type of separate gas-holder is also used to buffer extreme differences between gas-production and gas-use patterns.
 
*medium- or high-pressure gas-holders (8-10 bar / 200 bar)
 
  
{| cellspacing="0" cellpadding="0" border="0" class="IMGcenter"
+
{| cellpadding="10" border="0" align="right" class="IMGleft" style="width: 269px;"
|-
 
| style="width: 45%" | <br/>
 
| [[File:Bggasholdnicar.jpg|333px|RTENOTITLE]]<small class="IMGLEGEND">'''Biogas plant with seperate gasholder in Nicaragua'''</small><ref name="Photo: gtz/GATE">Photo: gtz/GATE</ref><br/>
 
| style="width: 45%" | <br/>
 
|}
 
 
 
Neither system can be considered for use in small-scale biogas plants. Even for large-scale plants, they cannot be recommended under the conditions in most developing countries. High-pressure gas storage in steel cylinders (as fuel for vehicles) is presently under discussion. While that approach is possible in theory, it would be complicated and, except in special cases, prohibitively expensive. It would also require the establishment of stringent safety regulations.
 
 
 
<br/>
 
 
 
== Gas Pipe, Valves and Accessories<br/> ==
 
 
 
=== Biogas Piping<br/> ===
 
 
 
At least 60% of all non-functional biogas units are attributable to defect gas piping. Utmost care has to be taken, therefore, for proper installation. For the sake of standardization, it is advisable to select a single size for all pipes, valves and accessories.
 
 
 
The requirements for [[Piping Systems for Biogas Plants|biogas piping]], valves and accessories are essentially the same as for other gas installations. However, biogas is 100% saturated with water vapor and contains hydrogen-sulfide. Consequently, no piping, valves or accessories that contain any amounts of ferrous metals may be used for biogas piping, because they would be destroyed by corrosion within a short time. The gas lines may consist of standard galvanized steel pipes. Also suitable (and inexpensive) is plastic tubing made of rigid PVC or rigid PE. Flexible gas pipes laid in the open must be UV-resistant.
 
 
 
<br/>
 
 
 
<u>Steel Pipes</u><br/>
 
 
 
Galvanized steel water supply pipes are used most frequently, because the entire piping system (gas pipe, valves and accessories) can be made of universally applicable English/U.S. Customary system components, i.e. with all dimensions in inches. Pipes with nominal dimensions of 1/2" or 3/4" are adequate for small-to-midsize plants of simple design and pipe lengths of less than 30 m. For larger plants, longer gas pipes or low system pressure, a detailed pressure-loss (pipe-sizing) calculation must be performed.
 
 
 
When installing a gas pipe, special attention must be paid to:
 
*gas-tight, friction-type joints
 
*line drainage, i.e. with a [[Piping Systems for Biogas Plants#Water traps|water trap]] at the lowest point of the sloping pipe in order to empty water accumulation
 
*protection against mechanical impact
 
 
 
<br/>
 
 
 
{| cellpadding="10" border="0" align="right" style="width: 348px" class="IMGright"
 
 
|-
 
|-
 
|  
 
|  
[[File:Bgstirrer.jpg|348px|RTENOTITLE]]
+
[[File:Bgstirring.gif|thumb|right|200px]]<br/><br/>
 
 
<small class="IMGLEGEND">'''Stirring device for a european biodigester'''</small><ref name="Photo: Krieg">Photo: Krieg</ref>
 
 
 
|}
 
 
 
= Stirring Facilities<br/> =
 
 
 
Optimum stirring substantially reduces the retention time. If [[Agitation of Digesters|agitation]] is excessive, the bacteria have "no time to eat". The ideal is gentle but intensive stirring about every four hours. Of similar importance is the breaking up of a scum layer which has lost contact with the main volume of substrate and is, therefore, not further digested. This top layer can form an impermeable barrier for biogas to move up from the digester to the gas holder.
 
 
 
As a rule of thumb it can be stated that stirring facilities are more important in larger plants than in small scale farm plants.
 
  
{| cellpadding="10" border="0" align="left" style="width: 400px" class="IMGleft"
 
|-
 
| [[File:Bgstirring.gif|400px|RTENOTITLE]]<small class="IMGLEGEND">'''Stirring facilities in the digester'''</small><ref name="Source: OEKOTOP">Source: OEKOTOP</ref><br/>
 
 
|}
 
|}
  
<br/>
+
Optimum stirring substantially reduces the retention time. If [[Agitation_of_Digesters|agitation]] is excessive, the bacteria have "no time to eat". The ideal is gentle but intensive stirring about every four hours. Of similar importance is the breaking up of a scum layer which has lost contact with the main volume of substrate and is, therefore, not further digested. This top layer can form an impermeable barrier for biogas to move up from the digester to the gas holder.As a rule of thumb it can be stated that stirring facilities are more important in larger plants than in small scale farm plants.<br/><u>Types of Stirring Facilities</u>:<br/>
 
 
<br/>
 
 
 
== Types of Stirring Facilities<br/> ==
 
  
 
#The '''''impeller stirrer''''' has given good results especially in sewage treatment plants.
 
#The '''''impeller stirrer''''' has given good results especially in sewage treatment plants.
 
#The '''''horizontal shaft''''' stirs the fermentation channel without mixing up the phases. Both schemes originate from large-scale plant practice.
 
#The '''''horizontal shaft''''' stirs the fermentation channel without mixing up the phases. Both schemes originate from large-scale plant practice.
#For simple household plants, '''''poking with a stick''''' is the simplest and safest stirring method.<br/>
+
#For simple household plants, '''''poking with a stick''''' is the simplest and safest stirring method.
  
 
<br/>
 
<br/>
Line 232: Line 91:
 
= Heating Systems<br/> =
 
= Heating Systems<br/> =
  
Normally, because of the rather high involved costs, small-scale biogas plants are built without [[Digester Heating|heating systems]]. But even for small scale plants, it is of advantage for the bio-methanation process to warm up the influent substrate to its proper process temperature before it is fed into the digester. If possible, cold zones in the digester should be avoided (see also [[Parameters and Process Optimisation for Biogas#Substrate temperature|substrate temperature]]).
+
Normally, because of the rather high involved costs, small-scale biogas plants are built without [[Digester_Heating|heating systems]]. But even for small scale plants, it is of advantage for the bio-methanation process to warm up the influent substrate to its proper process temperature before it is fed into the digester. If possible, cold zones in the digester should be avoided (see also [[Parameters_and_Process_Optimisation_for_Biogas#Substrate_temperature|substrate temperature]]). There are a number of different ways to get the required amount of thermal energy into the substrate are described. <u>In principle, one can differentiate between:</u>
 
 
In the following, a number of different ways to get the required amount of thermal energy into the substrate are described.
 
  
<u>In principle, one can differentiate between:</u>
 
 
*'''direct heating''' in the form of steam or hot water, and
 
*'''direct heating''' in the form of steam or hot water, and
 
*'''indirect heating''' via heat exchanger, whereby the heating medium, usually hot water, imparts heat while not mixing with the substrate.
 
*'''indirect heating''' via heat exchanger, whereby the heating medium, usually hot water, imparts heat while not mixing with the substrate.
  
<br/>
+
<br/>[[Digester_Heating|►]][[Digester_Heating|More information here...]].
 
 
== Direct Heating<br/> ==
 
 
 
Direct heating with steam has the serious disadvantage of requiring an elaborate steam-generating system (including desalination and ion exchange as water pretreatment) and can also cause local overheating. The high cost is only justifiable for large-scale sewage treatment facilities.
 
 
 
The injection of hot water raises the water content of the slurry and should only be practiced if such dilution is necessary.
 
 
 
<br/>
 
 
 
== Indirect Heating<br/> ==
 
 
 
Indirect heating is accomplished with heat exchangers located either inside or outside of the digester, depending on the shape of the vessel, the type of substrate used, and the nature of the operating mode.
 
#'''Floor heating''' systems have not served well in the past, because the accumulation of sediment gradually hampers the transfer of heat.
 
#'''In-vessel''' heat exchangers are a good solution from the standpoint of heat transfer as long as they are able to withstand the mechanical stress caused by the mixer, circulating pump, etc. The larger the heat-exchange surface, the more uniformly heat distribution can be effected which is better for the biological process.
 
#'''On-vessel''' heat exchangers with the heat conductors located in or on the vessel walls are inferior to in-vessel-exchangers as far as heat-transfer efficiency is concerned, since too much heat is lost to the surroundings. On the other hand, practically the entire wall area of the vessel can be used as a heat-transfer surface, and there are no obstructions in the vessel to impede the flow of slurry.
 
#'''Ex-vessel''' heat exchangers offer the advantage of easy access for cleaning and maintenance.
 
 
 
<br/>
 
 
 
While in Northern countries, often a substantial amount of the produced biogas is consumed to provide process energy, in countries with higher temperatures and longer sunshine hours, solar-heated water can be a cost-effective solution for heating. Exposing the site of the biogas plant to sunshine, e.g. by avoiding tree shade, is the simplest method of heating.
 
 
 
<br/>
 
  
 
= Pumps =
 
= Pumps =
  
[[Pumps for Biogas Plants|Pumps]] become necessary parts of a biogas unit, when the amounts of substrate require fast movement and when gravity cannot be used for reasons of topography or substrate characteristics. Pumps transport the substrate from the point of delivery through all the stages of fermentation. Therefore, several pumps and types of pumps may be needed. Pumps are usually found in large scale biogas units.
+
Pumps become necessary parts of a biogas unit, when the amounts of substrate require fast movement and when gravity cannot be used for reasons of topography or substrate characteristics. Pumps transport the substrate from the point of delivery through all the stages of fermentation. Therefore, several pumps and types of pumps may be needed. Pumps are usually found in large scale biogas units.
 
 
There are two predominant types of pump for fresh substrate: '''centrifugal pumps''' and '''positive-displacement pumps''' (reciprocating pumps). Centrifugal pumps operate on the principle of a rapidly rotating impeller located in the liquid flow. They provide high delivery rates and are very robust, i.e. the internals are exposed to little mechanical stress. They do, however, require a free-flowing intake arrangement, because they are not self-priming (regenerative).
 
 
 
Practically all centrifugal pump characteristics are geared to water. They show the delivery rates for various heads, the achievable efficiency levels, and the power requirement for the pump motor. Consequently, such data cannot be directly applied to biogas systems, since the overall performance and efficiency level of a pump for re-circulating slurry may suffer a serious drop-off as compared to its standard "water" rating (roughly 5-10%).
 
  
== Rotary Pump ==
+
== Types of Pumps ==
  
Rotary pumps are commonplace in liquid-manure pumping. They are eminently suitable for runny substrates.<br/>A rotary pump has an impeller turning inside a fixed body. The impeller accelerates the medium, and the resulting increase in flow velocity is converted into head or pressure at the rotary pump's discharge nozzle. The shape and size of the impeller can<br/>vary, depending on requirements. The cutter-impeller pump is a special kind of rotary pump. The impeller has hardened cutting edges designed to comminute the substrate.
+
► [[Pumps_for_Biogas_Plants|Read more here....]]
  
 
<br/>
 
<br/>
  
=== Limitation of a Centrifugal Pump ===
+
= Weak Ring<br/> =
 
 
Sometimes, namely when the substrate is excessively viscous, a centrifugal pump will no longer do the job, because the condition of the substrate surpasses the pump's physical delivery capacity. In such cases, one must turn to a so-called positive-displacement or reciprocating type of pump in the form of a piston pump, gear pump or eccentric spiral pump, all of which operate on the principle of displacing action to provide positive delivery via one or more enclosed chambers.
 
  
 +
{| cellpadding="10" border="0" align="right" class="IMGleft" style="width: 304px"
 +
|-
 +
| style="width: 276px" | [[File:Weakstrongring.jpg|thumb|right|280px]]<br/>
 
<br/>
 
<br/>
  
== Positive Displacement Pumps<br/> ==
+
|}
 
 
Positive displacement pumps offer multiple advantages. Even for highly viscous substrate, they provide high delivery and high efficiency at a relatively low rate of power consumption. Their characteristics - once again for water - demonstrate how little the delivery rate depends on the delivery head. Consequently, most of the characteristics show the delivery rate as a function of pump speed.
 
 
 
The main disadvantage as compared to a centrifugal pump is the greater amount of wear and tear on the internal occasioned by the necessity of providing an effective seal between each two adjacent chambers.
 
 
 
The speed of a positive-displacement pump can be varied to control delivery rate. This matches pump control more closely to precision metering of the substrate.The pressure stability of these self-priming pumps is better than that of rotary pumps, which means that delivery rate is much less dependent on head. Positive- displacement pumps are relatively susceptible to interfering substances, so it makes sense to install comminutors and foreign-matter separators to protect the pumps against coarse and fibrous constituents in the substrate<ref name="guide">FNR, 2012: Guide to biogas</ref>.
 
 
 
<br/>
 
  
'''Rotary-displacement pumps and eccentric singlerotor screw pumps''' are the most commonly used. Eccentric single-rotor screw pumps have a rotor shaped like a corkscrew running inside a stator made of an elastically resilient material. The action of the rotor produces an advancing space in which the substrate is transported.
+
The weak/strong ring improves the gas-tightness of [[Fixed-dome_Biogas_Plants|fixed-dome plants]] It was first introduced in Tanzania and showed promising results. The weak ring separates the lower part of the hemispherical digester, (filled with digesting substrate), from the upper part (where the gas is stored). Vertical cracks, moving upwards from the bottom of the digester, are diverted in this ring of lean mortar into horizontal cracks. These cracks remain in the slurry area where they are of no harm to the gas-tightness. The strong ring is a reinforcement of the bottom of the gas-holder, it could also be seen as a foundation of the gas-holder. It is an additional device to prevent cracks from entering the gas-holder. Weak and strong ring have been successfully combined in the CAMARTEC design<br/><u>Materials and Construction</u><br/>The weak ring consists of mortar of a mixture of sand, lime and cement (15:3:1). The top of the weak ring restores the horizontal level. It is interrupted only by the inlet pipe passing through. The strong ring rests on the weak ring and is the first layer of the upper part of the hemispherical shell. It consists of a row of header bricks with a concrete package at the outside. In case of soft or uncertain ground soil one may place a ring reinforcement bar in the concrete of the strong ring. The brick of the strong ring should be about three times wider than the brickwork of the upper wall. A detailed description of the weak/strong ring construction can be found in Sasse, Kellner, Kimaro (1991).<br/>
  
<br/>
+
= Pre-digestion Pit for Storage of Substrates =
  
 +
<u>Sizing depends on:</u> substrate arisings, digester capacity, length of time to be bridged between successive deliveries, land-use specifics and yield of co-substrates, supply contracts for substrates from off-site sources, possible disruptions in operation<br/><u>Special considerations:</u>
  
 +
*Avoid the possibility of storage plant freezing, for example by siting storage tanks indoors, heating storage containers or locating the plant for pits below grade level
 +
*Avoid biodegradation processes that reduce gas yield
 +
*Do not permit intermingling of hygienically problematic and hygienically acceptable substrates
 +
*Implement suitable structural measures to minimise odours
 +
*Avoid material emissions to soil and to the surface and underground water system
  
[[File:Eccentric single-rotor screw pump .JPG|frame|center|Eccentric single-rotor screw pump .JPG]]<br/>  
+
<br/><u>Designs</u> Containers for storing solid substrates in widespread use in agriculture, such as mobile silos, upright silos, plastic-tunnel silos and round-bale silos and open or roofed storage areas (e.g. solid-manure deposits) and pits/hoppers Containers for storing liquid substrates in widespread use in agriculture, such as tanks and predigester pits<br/><u>Costs</u> Storage facilities are generally in place; when new builds are needed the price has to be calculated on<br/>a case-to-case basis factoring in the multiplicity of influencing variables indicated above<br/>
  
 +
= Measurement Instruments<br/> =
  
 +
Flow-measuring devices (in the pipes) Ultrasonically (pre pits) Radar (pre-pits)<br/>Wheel loader scales
  
 
<br/>
 
<br/>
  
Rotary displacement pumps have two counter-rotating rotary pistons with between two and six lobes in an oval body. The two pistons counter-rotate and counterroll with low axial and radial clearance, touching neither each other nor the body of the pump. Their geometry is such that in every position a seal is maintained between the suction side and the discharge side of the pump. The medium is drawn in to fill the spaces on the suction side and is transported to the discharge side<ref name="guide">FNR, 2012: Guide to biogas</ref>.
+
= Further Information =
  
<br/>
+
*[[Portal:Biogas|Biogas Portal on energypedia]]
  
 
<br/>
 
<br/>
  
[[File:Rotary displacement pump.JPG|frame|center|Rotary displacement pump.JPG]]
+
'''<u>Information on materials and devices used in the construction of biogas plants:</u>'''
  
<br/>
+
*[[Checklist_for_the_Construction_of_a_Biogas_Plant|Checklist for the Construction of a Biogas Plant]]
 +
*[[Agitation_of_Digesters|Agitation of Digesters]]
 +
*[[Digester_Heating|Digester Heating]]
 +
*[[Piping_Systems_for_Biogas_Plants|Piping Systems for Biogas Plants]]
 +
*[[Plasters_and_Coats_for_Biogas_Digesters_and_Gas-holder|Plasters and Coats for Biogas Digesters and Gas-holder]]
 +
*[[Pumps_for_Biogas_Plants|Pumps for Biogas Plants]]
 +
*[[Slurry-Use_Equipment|Slurry-Use Equipment]]
 +
*[[Biogas_Implementation_-_Groundwater_Management|Biogas Implementation - Groundwater Management]]
  
<br/>
+
<br/><u>'''Web based sources'''</u>
  
<br/>
+
*[http://biogas.ifas.ufl.edu/ad_development/documents/biogasplants.pdf biogas.ifas - biogasplants (pdf])
 
+
*[[Checklist_for_the_Construction_of_a_Biogas_Plant|Checklist for the Construction of a Biogas Plant]]
== Pump Delivery Lines<br/> ==
+
*[http://www.haase-energietechnik.de/en/Products_and_Services/24-e_BiogasBrochure_Feb2011_1.pdf haase-energietechnik - BiogasBrochure (pdf)]
 
 
Pump delivery lines can be made of steel, PVC (rigid) or PE (rigid or flexible), as well as appropriate flexible pressure tubing made of reinforced plastic or rubber. Solid substrate, e.g. dung, can also be handled via conveyor belt, worm conveyor or sliding-bar system, though none of these could be used for liquid manure. When liquid manure is conducted through an open gutter, small weirs or barrages should be installed at intervals of 20-30 m as a means of breaking up the scum layer.
 
 
 
Each such barrier should cause the scum to fall at least 20-30 cm on the downstream side. All changes of direction should be executed at right angles (90°). Depending on the overall length, the cross gutter should be laid some 30-50 cm deeper than the main gutter. Transitions between a rectangular channel and a round pipe must be gradual. An inclination of about 14% yields optimum flow conditions. The channel bottom must be laid level, since any slope in the direction of flow would only cause the liquid manure to run off prematurely. All wall surfaces should be as smooth as possible.
 
  
 
<br/>
 
<br/>
  
= Weak Ring<br/> =
+
= References<br/> =
 
 
=== <span style="line-height: 1.5em; font-size: 0.85em;">The weak/strong ring improves the gas-tightness of </span>[[Types of Biogas Digesters and Plants#Fixed-dome plants|fixed-dome plants]]<span style="line-height: 1.5em; font-size: 0.85em;">. It was first introduced in Tanzania and showed promising results. The weak ring separates the lower part of the hemispherical digester, (filled with digesting substrate), from the upper part (where the gas is stored). Vertical cracks, moving upwards from the bottom of the digester, are diverted in this ring of lean mortar into horizontal cracks. These cracks remain in the slurry area where they are of no harm to the gas-tightness. The strong ring is a reinforcement of the bottom of the gas-holder, it could also be seen as a foundation of the gas-holder. It is an additional device to prevent cracks from entering the gas-holder. Weak and strong ring have been successfully combined in the </span>[[Types of Biogas Digesters and Plants#Fixed-dome plants|CAMARTEC design]]<span style="line-height: 1.5em; font-size: 0.85em;">.</span> ===
 
  
{| class="IMGcenter" cellpadding="0" cellspacing="0" border="0"
+
<references />
|-
 
| style="width: 45%;" | <br/>
 
| [[File:Weakstrongring.jpg|552px|RTENOTITLE]]<small class="IMGLEGEND">'''Photo<ref name="Kellner (TBW)">Kellner (TBW)</ref>: Construction of the weak/strong ring of a 16 m<sup>3</sup>, Tanzania'''</small><br/>
 
| style="width: 45%;" | <br/>
 
|}
 
 
 
<!-- weakring.gif Sasse, Kellner, Kimaro, GATE, 1991 -->
 
 
 
<br/>
 
 
 
<u>Materials and Construction</u><br/>
 
 
 
The weak ring consists of mortar of a mixture of sand, lime and cement (15:3:1). The top of the weak ring restores the horizontal level. It is interrupted only by the inlet pipe passing through. The strong ring rests on the weak ring and is the first layer of the upper part of the hemispherical shell. It consists of a row of header bricks with a concrete package at the outside. In case of soft or uncertain ground soil one may place a ring reinforcement bar in the concrete of the strong ring. The brick of the strong ring should be about three times wider than the brickwork of the upper wall. A detailed description of the weak/strong ring construction can be found in Sasse, Kellner, Kimaro (1991).
 
 
 
= <span style="font-size: 19px; line-height: 23.799999237060547px;">Further Information</span> =
 
  
 
*'''Ringkamp, M.; Tentscher, W.; Schiller, H.''': Preliminary results on: statical optimization of family-sized fixed-dome digesters. Tilche, A.; Rozzi, A. (ed.): Poster Papers. Fifth International Symposium on Anaerobic Digestion, Bologna 1988, pp. 321-324
 
*'''Ringkamp, M.; Tentscher, W.; Schiller, H.''': Preliminary results on: statical optimization of family-sized fixed-dome digesters. Tilche, A.; Rozzi, A. (ed.): Poster Papers. Fifth International Symposium on Anaerobic Digestion, Bologna 1988, pp. 321-324
 
*'''Sasse, L.; Kellner, Ch.; Kimaro, A.''': Improved Biogas Unit for Developing Countries. Deutsche Gesellschaft für Technische Zusammenarbeit (GTZ) GmbH, Vieweg & Sohn Verlagsgesellschaft Braunschweig, 1991
 
*'''Sasse, L.; Kellner, Ch.; Kimaro, A.''': Improved Biogas Unit for Developing Countries. Deutsche Gesellschaft für Technische Zusammenarbeit (GTZ) GmbH, Vieweg & Sohn Verlagsgesellschaft Braunschweig, 1991
 +
*J.; Sasse, L. (Deutsche Gesellschaft für Technische Zusammenarbeit): Production and utilization of biogas in rural areas of industrialized and developing countries. TZ-Verlagsgesellschaft mbH, Roßdorf, 1986, 278 S.&lt;/span&gt;
  
[[Biogas|-> Back to "Biogas Portal"]]
+
<br/>
  
 
[[Category:Biogas]]
 
[[Category:Biogas]]

Latest revision as of 09:01, 8 April 2015

►Back to Biogas Portal

Overview

The feed material is mixed with water in the influent collecting tank The fermentation slurry flows through the inlet into the digester. The bacteria from the fermentation slurry are intended to produce biogas in the digester. For this purpose, they need time. Time to multiply and to spread throughout the slurry. The digester must be designed in a way that only fully digested slurry can leave it. The bacteria are distributed in the slurry by stirring (with a stick or stirring facilities). The fully digested slurry leaves the digester through the outlet into the slurry storage.The biogas is collected and stored until the time of consumption in the gasholder. The gas pipe carries the biogas to the place where it is consumed by gas appliances. Condensation collecting in the gas pipe is removed by a water trap. Depending on the available building material and type of plant under construction, different variants of the individual components are possible. The following (optional) components of a biogas plant can also play an important role and are described seperatly: Heating systems, pumps, weak ring.

Influent Collecting Tank

Bgfixeddomeinst.jpg


Size and Homogenization
Fresh substrate is usually gathered in an influent collecting tank prior to being fed into the digester. Depending on the type of system, the tank should hold one to two days' substrate. An influent collecting tank can also be used to homogenize the various substrates and to set up the required consistency, e.g. by adding water to dilute the mixture of vegetable solids (straw, grass, etc.), or by adding more solids in order to increase the bio-mass. The fibrous material is raked off the surface, if necessary, and any stones or sand settling at the bottom are cleaned out after the slurry is admitted to the digester. The desired degree of homogenization and solids content can be achieved with the aid of an agitator, pump or chopper. A rock or wooden plug can be used to close off the inlet pipe during the mixing process.


Location

A sunny location can help to warm the contents before they are fed into the digester in order to avoid thermal shock due to the cold mixing water. In the case of a biogas plant that is directly connected to the stable, it is advisable to install the mixing pit deep enough to allow installation of a floating gutter leading directly into the pit. Care must also be taken to ensure that the low position of the mixing pit does not result in premature digestion. For reasons of hygiene, toilets should have a direct connection to the inlet pipe.


Inlet and Outlet

The inlet (feed) and outlet (discharge) pipes lead straight into the digester at a steep angle. For liquid substrate, the pipe diameter should be 10-15 cm, while fibrous substrate requires a diameter of 20-30 cm. The inlet and the outlet pipe mostly consist of plastic or concrete.


Position
Both the inlet and the outlet pipe must be freely accessible and straight, so that a rod can be pushed through to eliminate obstructions and agitate the digester contents. The pipes should penetrate the digester wall at a point below the lowest slurry level (i.e. not through the gas storage). The points of penetration should be sealed and reinforced with mortar. The inlet pipe ends higher in the digester than the outlet pipe in order to promote more uniform flow of the substrate. In a fixed-dome plant, the inlet pipe defines the bottom line of the gas-holder, acting like a security valve to release over-pressure. In a floating-drum plant, the end of the outlet pipe determines the digester's (constant) slurry level. Inlet and outlet pipe must be placed in connection with brick-laying. It is not advisable to break holes into the spherical shell afterwards, this would weaken the masonry structure.


Toilet Connection at the Inlet
Household Toilets can be connected to a Biogas Digester.

Digester

In general terms, digesters consist of the digestion tank as such, which is thermally insulated, plus a heating system, mixer systems and discharge systems for sediments and the spent substrate.

Raw Material for Biogas Digesters

Read more here .....

Types of Biogas Digesters

Read more here .....

Types of Gasholders for Biogas Plants

Read more here .....

Gas Pipe, Valves and Accessories

Biogas Piping

Bgstirrer.jpg


At least 60% of all non-functional biogas units are attributable to defect gas piping. Utmost care has to be taken, therefore, for proper installation. For the sake of standardization, it is advisable to select a single size for all pipes, valves and accessories. The requirements for biogas piping, valves and accessories are essentially the same as for other gas installations. However, biogas is 100% saturated with water vapor and contains hydrogen-sulfide. Consequently, no piping, valves or accessories that contain any amounts of ferrous metals may be used for biogas piping, because they would be destroyed by corrosion within a short time. The gas lines may consist of standard galvanized steel pipes. Also suitable (and inexpensive) is plastic tubing made of rigid PVC or rigid PE. Flexible gas pipes laid in the open must be UV-resistant.


► Read More here...

Water Traps

► Read more here....

Valves

► Read more here...

Gas Analysis Equipment

►Read more here...

Stirring Facilities

Bgstirring.gif


Optimum stirring substantially reduces the retention time. If agitation is excessive, the bacteria have "no time to eat". The ideal is gentle but intensive stirring about every four hours. Of similar importance is the breaking up of a scum layer which has lost contact with the main volume of substrate and is, therefore, not further digested. This top layer can form an impermeable barrier for biogas to move up from the digester to the gas holder.As a rule of thumb it can be stated that stirring facilities are more important in larger plants than in small scale farm plants.
Types of Stirring Facilities:

  1. The impeller stirrer has given good results especially in sewage treatment plants.
  2. The horizontal shaft stirs the fermentation channel without mixing up the phases. Both schemes originate from large-scale plant practice.
  3. For simple household plants, poking with a stick is the simplest and safest stirring method.


Heating Systems

Normally, because of the rather high involved costs, small-scale biogas plants are built without heating systems. But even for small scale plants, it is of advantage for the bio-methanation process to warm up the influent substrate to its proper process temperature before it is fed into the digester. If possible, cold zones in the digester should be avoided (see also substrate temperature). There are a number of different ways to get the required amount of thermal energy into the substrate are described. In principle, one can differentiate between:

  • direct heating in the form of steam or hot water, and
  • indirect heating via heat exchanger, whereby the heating medium, usually hot water, imparts heat while not mixing with the substrate.


More information here....

Pumps

Pumps become necessary parts of a biogas unit, when the amounts of substrate require fast movement and when gravity cannot be used for reasons of topography or substrate characteristics. Pumps transport the substrate from the point of delivery through all the stages of fermentation. Therefore, several pumps and types of pumps may be needed. Pumps are usually found in large scale biogas units.

Types of Pumps

Read more here....


Weak Ring

Weakstrongring.jpg


The weak/strong ring improves the gas-tightness of fixed-dome plants It was first introduced in Tanzania and showed promising results. The weak ring separates the lower part of the hemispherical digester, (filled with digesting substrate), from the upper part (where the gas is stored). Vertical cracks, moving upwards from the bottom of the digester, are diverted in this ring of lean mortar into horizontal cracks. These cracks remain in the slurry area where they are of no harm to the gas-tightness. The strong ring is a reinforcement of the bottom of the gas-holder, it could also be seen as a foundation of the gas-holder. It is an additional device to prevent cracks from entering the gas-holder. Weak and strong ring have been successfully combined in the CAMARTEC design
Materials and Construction
The weak ring consists of mortar of a mixture of sand, lime and cement (15:3:1). The top of the weak ring restores the horizontal level. It is interrupted only by the inlet pipe passing through. The strong ring rests on the weak ring and is the first layer of the upper part of the hemispherical shell. It consists of a row of header bricks with a concrete package at the outside. In case of soft or uncertain ground soil one may place a ring reinforcement bar in the concrete of the strong ring. The brick of the strong ring should be about three times wider than the brickwork of the upper wall. A detailed description of the weak/strong ring construction can be found in Sasse, Kellner, Kimaro (1991).

Pre-digestion Pit for Storage of Substrates

Sizing depends on: substrate arisings, digester capacity, length of time to be bridged between successive deliveries, land-use specifics and yield of co-substrates, supply contracts for substrates from off-site sources, possible disruptions in operation
Special considerations:

  • Avoid the possibility of storage plant freezing, for example by siting storage tanks indoors, heating storage containers or locating the plant for pits below grade level
  • Avoid biodegradation processes that reduce gas yield
  • Do not permit intermingling of hygienically problematic and hygienically acceptable substrates
  • Implement suitable structural measures to minimise odours
  • Avoid material emissions to soil and to the surface and underground water system


Designs Containers for storing solid substrates in widespread use in agriculture, such as mobile silos, upright silos, plastic-tunnel silos and round-bale silos and open or roofed storage areas (e.g. solid-manure deposits) and pits/hoppers Containers for storing liquid substrates in widespread use in agriculture, such as tanks and predigester pits
Costs Storage facilities are generally in place; when new builds are needed the price has to be calculated on
a case-to-case basis factoring in the multiplicity of influencing variables indicated above

Measurement Instruments

Flow-measuring devices (in the pipes) Ultrasonically (pre pits) Radar (pre-pits)
Wheel loader scales


Further Information


Information on materials and devices used in the construction of biogas plants:


Web based sources


References


  • Ringkamp, M.; Tentscher, W.; Schiller, H.: Preliminary results on: statical optimization of family-sized fixed-dome digesters. Tilche, A.; Rozzi, A. (ed.): Poster Papers. Fifth International Symposium on Anaerobic Digestion, Bologna 1988, pp. 321-324
  • Sasse, L.; Kellner, Ch.; Kimaro, A.: Improved Biogas Unit for Developing Countries. Deutsche Gesellschaft für Technische Zusammenarbeit (GTZ) GmbH, Vieweg & Sohn Verlagsgesellschaft Braunschweig, 1991
  • J.; Sasse, L. (Deutsche Gesellschaft für Technische Zusammenarbeit): Production and utilization of biogas in rural areas of industrialized and developing countries. TZ-Verlagsgesellschaft mbH, Roßdorf, 1986, 278 S.</span>