Flexibility (Power System)

Flexibility: Concept Definition

According to the International Energy Agency, the flexibility of a power system refers to "the extent to which a power system can modify electricity production or consumption in response to variability, expected or otherwise". Another source described it as "the modification of generation injection and/or consumption patterns in reaction to an external signal (price signal or activation) in order to provide a service within the energy system" .

Flexibility can therefore refer to the capability to change power supply/demand of the system as a whole or a particular unit (eg. a power plant or a factory).

Flexibility: Why It Matters

Load balancing is not the only service a power system must perform flexibilty. There are many other services the operators of a power system must consider to make the grid stable. The three main services for the reliability of a power system are: load balancing, frequency response, and voltage response.

Renewable sources, together with some battery storage, can already perform some of these services better than a conventional power system. For example, renewable sources can supply reactive power (and therefore voltage response) even when they are not giving real power, and batteries can perform frequency response better than conventional sources. Currently a renewable power source integrated with a battery storage system is already cost competitive to some conventional sources, and such implementation will boost the reliability of the grid.

However, current capacity of dispatchable renewables or batteriers are not enough to cover variations of the residual load curve. So the residaul load flexibility of a power system must still be performed mainly by conventional dispatchable sources, with the aid of some demand response.

For example, below is a simulated power output profile of the power system in Taiwan by summer 2025. Since most renewable capacity by then will be solar, there exists an obvious "duck curve" in this profile. The total dispatchable renewable capacity (hydro, pumped storage, bioenergy and geothermal) is about 5.5GW, but variations of the residual load can ramp up to 18GW in six hours, so in this specific redispatchment scenario fossil gas power plants perform most of the residual load flexibility.

800px

Flexibility: Supply Side

Conventional Flexible Power Plants

Conventional flexible power plants, mainly the gas power plants, play an important role of varying power output flexibly. This is already the case in the traditional power systems, which is known as "load following". They will continue to play the same role when more variable renewables are fed into the grid, only to a greater extent.

Power plants which are conventionally considered inflexible, such as hard coal power plants or even lignite power plants, can be retrofitted or redesigned to become more flexible. This is what has happened in countries like Germany and Denmark.

The role of nuclear power plants in providing residual load flexibility is more unclear. Ramping the power output of nuclear power plants significantly tend to damage the revenues and lifespan of the plants heaviliy. In countries where a clear nuclear phase out plan has been set, this is less of a problem; the nuclear fleet in Germany performed some 40% of power reduction during storms in autumn 2017. In countries where nuclear is likely to remain online for a while, this kind of flexible behavior is seldom observed; for example in Ontario, with only 6% of variable renewable electricity share, the operators already have to curtail 26% of the VRE generations in order to avoid shutting down nuclear power plants; in Germany this statistic is around 1%. France is perhaps one exception, since its nuclear fleet is too large that load following for some of the plants is almost unavoidable .

Interconnection

Better interconnections between grids can also ease some of the flexibility demand to neighboring grids. The more flexible dispatchable power plants are well connected in the system, the less ramping any single power plant will need to perform. Interconnections can also bringdown the wholesale electricity prices of the neighboring grid because electricity production with higher marginal costs can be reduced.

However, conventional electricity sources may choose to export electricity rather than ramping down shutting down more often when interconnection is better. This causes a difficulty to reduce conventional electricity generation to full potential. For example, people have been suggesting that brown coal electricity generation in Germany could have dropped by 37%, should there be no electricity export and all the additional residual load flexibility was performed by brown coal power plants.

Flexibility: Demand Side

Flexibility on the demand side is typically known as demand response. Like conventional power plants, industrial owners can retrofit their factories or redesign their control system under the new mindset to meet the growing demand of residual load flexibility.

An example of this occurred during a solar eclipse event in Germany in 2015. Aluminium factories were asked to lower power demand during the few minutes, and the grid went through the event with no major incident.

Ways to Improve Flexibility

Technical Measures: Retrofit and New Design Mindset

There are three important factors that indicate the flexibility of a conventional power plant: the start-up time, the ramp rate, and the minimum load.

For existing conventional plants, retrofitting them may be able to increase their flexibility. One example is to add a pulverized coal (PC) storage facility and thereby decouples the direct supply chain between mills and burners. By doing so, the coal power plant can run at a lower minimum load because of the faster responses to fire instabilities. It can also provide a higher ramp rate because of a reduced time lag between mills and burners.

For newly built conventional power plants, flexibility must be in the center role when designing. For instance, in the past when conventional power plants were designed to run around the clock with little variation of power output, the main consideration was to ensure that the inner components could withstand the high pressure and high temperature within the power plant; now engineers must also consider the thermal stress of the materials during a major ramp event.

Market Measures: Real Time Markets and Incentives

Apart from retrofitting existing conventional power plants or build new ones under a new design mindset, the electricity market can also boost the flexibility of the overall system, if designed properly.