Grain Mill

From energypedia
Revision as of 14:55, 9 August 2012 by ***** (***** | *****)

Overview

To prepare the cereals for further processing, the chaff has to be separated from grain, either manually with a winnowing tray or mechanically by a powered shaker or grinder. Mechanical power is also available for dehusking rice or shelling maize as an alternative to manual work with rice hullers or huskers and maize shellers. The same applies to other cereals and crops for which special machinery has been or is being developed. Bran as a by-product of dehulling cereals is a source of income if sold as poultry feed and other animal feed.
Milling transforms grain into flour for food preparation. The main crops that are milled are maize, rice, sorghum, teff and millet, using hammer or plate mills. A hammer mill crushes aggregate material into smaller pieces with hammers (beaters) made from hardened alloy steel which are rectangular for efficient grinding. Hammer mills are also used to pulverise by-products of coconuts (copra), palm kernels & other oil seeds (press cake). Wheat is milled with roller mills but these are too expensive for small-scale operations. Although demand may be highest during the harvest season, grain milling is required throughout the year as many households keep a stock of grain
Most operations utilise energy derived from mechanical power, with many alternatives for technologies powered by human, animal, water or a stationary engine. Mechanised milling operations are far more efficient and far less labour intensive than manual methods, using wind/micro-hydro and hybrid power systems (wind/hydro/diesel) for energy intensive processing activities. Mills can be powered directly by transforming energy from sources such as wind or water or by electricity generated from a combination of fossil fuel-fired generators with wind or hydro power. Without electricity, grain mills are often driven by diesel motors, for example, in the so-called multi-functional platforms.


Technologies

There are several technologies available, and they can be grouped into technologies:

  • concerning the way the product is milled
  • concerning the way the motor is driven


Mill Technologies

Hammer mills etc.


Drive Technologies

DC Grain Mills

These are the so-called « solar » grain mills. For the sake of this article, a solar grain mill is a grain mill that is driven by direct current. The grain mill is used in a solar system that consists of the basic components (PV panels, batteries, charge controller, load). Common voltage levels are 12 V and 24 V.

DC grain mill with mill operator. This specific device is used for millet.

Advantages:

  • General advantages of decentralised solar systems: usable wherever the resource is available, can be sized to the need, etc.

Disadvantages:

  • Relatively high start-up currents require a start-up resistor which may brake easily.
  • The start-up current also means that the load (the mill) cannot be directly connected to the charge controller, but must be connected to the battery. The battery is thus not protected against deep discharge. Users must be trained to switch off the mill as soon as the charge controller indicates a deep discharge.

Technically, one could solve this problem by including a shunt that is governed by the load contact of the charge controller and that disconnects the mill as soon as the charge controller switches off the load. However, DC shunts are very expensive.

  • Requires battery maintenance.


AC Grain Mills

These are grain mills which are operated at 230 V. Basic models can be found with suppliers of agricultural equipment. These grain mills can be operated on the national grid or on minigrids.

In addition, these grain mills can also be driven with solar energy. This use case would require an inverter and batteries.


Diesel-driven Grain Mills

These can, for example, be found in multi-functional platforms. In this case, the diesel motor drives the grain mill via a transmission drive.


Practical Experiences

Senegal

PERACOD currently has two DC-driven grain mills in operation. These grain mills were bought locally. After initially receiving quotes for a product that seemed suitable, another product had to be bought since the provider could not deliver the product the project had originally aimed at.

After installation, problems occurred with the starting resistor, which broke and had to be replaced several times. Also, users manipulated the system, leading to several failures. The grain mills have had a disappointed performance ever since installation. A detailed technical monitoring is under way in order to study the problem further.

One of the first conclusion of the project was to not underestimate the amount of work necessary in the beginning to make the productive use work.

-> Please see a presentation here on some issues with solar grain mills in Senegal.


Pitfalls

Product Alteration

  • Grain mills may alter characteristics of the good that is milled.
  • The size of the resulting powder may be different from the size people are used to from other milling techniques. This can result in changes in the way the product can be used for food preparation and / or changes in taste.
  • In addition, grain may become hot in the grain mill and thus change its taste.


Types of Grain that can be Milled

Grain mills must be adapted to the type of product to be milled. There are several grain mills which can be adapted to different goods, for example, wheat, maize, or sorghum. Be careful when choosing a product and test it before deployment.

Millet before and after milling

Improper Sizing

When designing the system, one should take care of proper sizing of the mill and the associated power system. Key questions to be considered include:

  • What is the amount of grain that has to be milled on average, and in peak times? Can my (diesel / solar) system power the mill for a sufficient amount of time?
  • What is the output of the mill (in kg/day)? Does the output vary in function of the type of grain?
  • What is the "catchment area" of the mill, i.e., from how far will people come to mill their products?

Answering these questions will require technical / engineering knowledge (system design etc.), but also knowledge of people's habits.


Impact

Grain milling can greatly ease workload on women, as women are usually in charge of milling by hand with the help of a mortar and pestle.


References